| thejdm.com v6 [2026 rebirth] https://www.thejdm.com/forum/ Print view |
|
| Looking for a GOOD all motor exhaust for my EK hatch https://www.thejdm.com/forum/viewtopic.php?f=14&t=8068 |
Page 1 of 3 |
| Author: | Natural Aspirations [ March 16, 2007 ] |
| Post subject: | Looking for a GOOD all motor exhaust for my EK hatch |
Just looking for some advise on an exhaust for my Civic. Looking to make upwards of 210 whp and what something that flows well. Most of what I have found is 60mm I am looking for something a bit larger, my header outlet is 2.5" looking for no bottle necks. I had my heart set on a 70mm Skunk2 exhaust but they wont be out for another 2 months or so. Not a lot of companies make a 3" or anything above 60mm for the hatchback. Also not trying to spend more than $600.  |
|
| Author: | Jezek [ March 16, 2007 ] |
| Post subject: | |
Spoon N1. Simple as that. You can get the rear bolt on for about $350-$450 and then just get some 2.25" piping from the header back. I wouldn't get 3" for an all motor car, that's for sure. Some b00sted cars don't even need that much exhaust flow. |
|
| Author: | JDMJedi [ March 16, 2007 ] |
| Post subject: | |
^^ agreed some back pressure is important in an all motor car. |
|
| Author: | miyagi [ March 16, 2007 ] |
| Post subject: | |
2.5 inch mandrel bent piping, 2.5 in test pipe, 2.5 in high flow resonator, 2.5 in in/out flat black vibrant muffler. Looks stock, sounds a little deeper than stock, gives you just what you want. If you're feeling intense, go with some 2.75, i wouldn't go to 3" tho. The vibrant mufflers are 115 shipped all over the internet and on ebay, piping is cheap if you go to the right places too ... spend as little as possible on an exhaust - all the big name ones are over priced anyway... |
|
| Author: | miyagi [ March 16, 2007 ] |
| Post subject: | |
lol - dan, i didn't even realize this was your post... i just skimmed and replied. sooo in any event, go fuck yourself <3 |
|
| Author: | EK29K [ March 16, 2007 ] |
| Post subject: | |
i have the spoon n1 and love it |
|
| Author: | Natural Aspirations [ March 16, 2007 ] |
| Post subject: | |
Horrible misconception, It has been proven time and time again that a back pressure is not something you want. I have seen numerous dynos that prove this, one very good one by SMSP. |
|
| Author: | .rob [ March 17, 2007 ] |
| Post subject: | |
have you looked into T1R? or maybe JIC? skunk is really good for the civics, though. they actually devote their times into our cars. |
|
| Author: | Natural Aspirations [ March 17, 2007 ] |
| Post subject: | |
The T1r is very nice and I have been leaning towards that, the best deal on it I have found is 545 shipped. If I were able to get the 70mm Skunk2 I would be all over it, I can get the 60mm for ~425 shipped. I haven't looked into JIC at all, I will check them out |
|
| Author: | 01teggy [ March 17, 2007 ] |
| Post subject: | |
u want an exhaust that flows well, go with the buddyclub spec 2! its loud but it flows! and evasive has it for like $370!! |
|
| All times are UTC-04:00 | Page 1 of 3 |
|
Powered by phpBB® Forum Software © phpBB Limited |
|