Hey guys. Kotomile helped me find my way over here and thought you would like some of the stuff I offer. I know I am new here but here is some feedback I have gotten on another forum. http://www.miataturbo.net/forums/showthread.php?t=6036
The first big one is Devils Own Water/Methanol injection systems.
http://www.alcohol-injection.com
I have personally installed a few of these kits and the results have been awesome. I have a stock looking Neon SRT4 running around Denver with one that makes well over 400 whp on pump gas on the stock block. The car gets driven hard every single day and never misses a beat. Intake temps stay at ambient while under boost. Its really a no brainer mod to gain some nice power and safety. For you Greddy guys, how about not having to pull any timing while running 8+ psi? There have been gains seen as high as 60 whp using this kit. Anyway I will cut to the chase.
The basic kits will be $180:) shipped and the progressive kits with a controller will be $275:) shipped. I place your order with Devils Own the same day I recieve payment.
Here is a link to the install instructions so you can see how easy it is to install.
http://www.alcohol-injection.com/base_a ... ons_vc.pdf
For guys who want to ramp up the flow Vs boost you must have a map sensor.
I can provide GM sensors for those who want to do that.
Here is a great link explaining how water injection works http://www.rallycars.com/Cars/WaterInjection.html
Here is someone results by adding a Devils Own kit and a couple more pounds of boost.
http://www.alcohol-injection.com/forum/ ... l-290.html
I did an install on an S4 with k04/RS6 turbo. Dual 5 GPH nozzles.We used the factory washer fluid bottle as the reservoir.
Here is a log of before and after ignition timing. The blue is with the water injection on. The controller is still untuned.
Here is a graph showing that through just a short 3rd gear high rpm pull the car is almost .1 seconds faster. This is still at the same boost level. Running a full quarter mile may show .25 improvement. Not bad for under $300.
The next cool item I offer is the Tullos Tech electronic boost controller. You can check them out here http://www.tullostech.com/index.php?...ask=view&id=18Its a quality unit with all the features of something like a Greddy Profec II but it offers closed loop boost control that makes it really simple to dial in. Its also very tiny. I offer them for $275 shipped with solenoid.
Next up is AEM Uego Widebands with gauge and the AEM Tru Boost Electronic boost controller. Neither one of these probably need an introduction. I offer them both for $270 shipped.
Here is some other turbo parts for the DIYer that are from http://www.ATPturbo.com that I offer as well.Straight Couplers (All couplers are availabe in Black,Blue and Red)
1"(1foot piece) $7.50
1.25 (1foot piece) $8.25
2"
2.25
2.5
2.75 $5.25
3"
3.5 $5.75
4" $7.00
Hump Couplers
2"
2.25
2.5
2.75
3 $10.75
3.5"
4" $12.00
Transitions All transitions are $15.50
2-2.25
2-2.5
2-2.75
2-3
2.25-2.5
2.25-2.75
2.25-3
2.5-2.75
2.5-3
2.75-3
3-3.25
3-3.5
3-4
45 Degree Elbows
2"
2.25
2.5
2.75
3" $32
90 Degree Elbows
2"
2.25
2.5
2.75 $35
3 $37
4 $39
Tbolt Clamps
2"
2.25
2.5
2.75
3
3.25 $3.25
Straight Stainless Piping(Price is for 2 feet)
2"
2.25
2.5 $16.00
2.75
3" $19.50
45 Degree Stainless Elbows ( 6" Legs"
2"
2.25
2.5 $25.00
2.75
3" $27.00
90 Degree Stainless Bends
2"
2.25
2.5 $25.00
2.75 $27.00
3" $28.00
2.5" Stainless Flex Bellows for Downpipe Construction(6" long) $32.50
3" Stainless Flex Bellows(6" Long) $32.50
Tial 38mm Wastegate $205
Tial 44mm Wastegate $355
Tial 50mm BOV $202
BEGI Fising Rate Fuel Pressure Regulator $205
Turbine Heatshield $57
3" Vband Clamp w/2 flanges $40
Cast Aluminum 2" Bend (For welding onto compressor outlet) $21
Steel 5 Bolt T3 Turbine outlet flange with 3" Vband flange $75
Steel 5 Bolt T3 Turbine outler flange with built in internal wastegate and 3" Vband flange $150
Steel GT25/GT28 Turbne outlet flange with 3" Vband $85
T3/T4 aluminum oil drain flange $13
Turbos
Garrett
T3 60 trim .48 No wastegate $565
T3/TO4E 57Trim .63 $615
GT25R $815
GT28 $815
GT28RS (GT2860Disco Potato) $1025
GT3071R $1150
GT32(The Andy Floyd Turbo) $675
I can be reached anytime at 425-445-1068. I am online all day. My AIM name is Wideopentuning. Paypal is my prefered payment method. If you are interested in anything that I don't have in my post feel free to shoot me an email or IM and I will see what I can do. Thanks alot guys and I hope to hear from some of you. Kelly
