1996 Honda CB400SF Ver. S and 1994 Honda Civic Sir II
Project CRX waiting for my return in Vegas...
| thejdm.com v6 [2026 rebirth] https://www.thejdm.com/forum/ Print view |
|
| My EG6 + My CB400SF <3 JDM as it gets https://www.thejdm.com/forum/viewtopic.php?f=31&t=11106 |
Page 1 of 1 |
| Author: | meancivicsi [ December 14, 2011 ] |
| Post subject: | My EG6 + My CB400SF <3 JDM as it gets |
1996 Honda CB400SF Ver. S and 1994 Honda Civic Sir II Project CRX waiting for my return in Vegas... |
|
| Author: | 77 [ December 14, 2011 ] |
| Post subject: | Re: My EG6 + My CB400SF <3 JDM as it gets |
Nice, interested in seeing that CRX come together. |
|
| Author: | .saint [ December 14, 2011 ] |
| Post subject: | Re: My EG6 + My CB400SF <3 JDM as it gets |
likewise. nice on 3 levels. welcome back btw! |
|
| Author: | Zero [ December 15, 2011 ] |
| Post subject: | Re: My EG6 + My CB400SF <3 JDM as it gets |
hmm... where were you when i was in las vegas for 4 years lol. |
|
| Author: | meancivicsi [ December 16, 2011 ] |
| Post subject: | Re: My EG6 + My CB400SF <3 JDM as it gets |
Thanks everyone. I am also excited for the rex build. Right before a tune session i was sent to Japan so it sits in storage for now. Started as a freshly gunmetal painted 88 CRX hf shell Autopower 4 pt cage Simpson 5 pt harness Momo steering wheel integra DA brakes Hawk pads Goodridge braided SS lines N1 crank pulley brand new 88 crx side molding 88 crx hf front bumper reinforcement Innovate X-member Energy suspension master kit B&M Short shifter Invidia exhaust JG Edlebrock header with custome 2.5in collector by LDL motorsports Hondata S100 P28 OBD 1 ECU Mr. Gasket race dizzy and coil pack AEBS Intake ITR throttle body hondata Intake Mani gasket Tokico Blue struts Progress swap springs Progress rear anti-roll bar Cusco front strut tower brace MOOG ball joints through out Del sol 2 core rad + slim fan RC 310cc injectors walbro 255lph pump AN fuel feed line 15/16 DA master cylinder CUsco subframe brace Cusco LSD Skunk2 retainers Skunk2 valves Skunk2 dual valve springs Skunk2 Stage 2 cams Full port and polish + 3 angle valve job by LDL (outsourced to Arizona race and machine) ARP head studs ITR Oil pump ARP rod bolts shot peened rods CTR overbore pistons Balance and blueprinted by Dennis from LDL motorsports PC680 battery VIS SiR CF hood         @Zero You problably saw me rolling around in this...  or saw me at the auto hobby shop with my rex in pieces. |
|
| Author: | .saint [ December 17, 2011 ] |
| Post subject: | Re: My EG6 + My CB400SF <3 JDM as it gets |
damn  look at all those new parts  |
|
| Author: | SingleCamEJ8 [ December 19, 2011 ] |
| Post subject: | Re: My EG6 + My CB400SF <3 JDM as it gets |
new new new....looking good! |
|
| All times are UTC-04:00 | Page 1 of 1 |
|
Powered by phpBB® Forum Software © phpBB Limited |
|