new to thejdm

1bar_ek · Post by **1bar_ek** » September 27, 2005

Just registered today and wanted to say "HI." Found 'thejdm' out from a friend on honda-tech.com. Will have my ride up soon. 98 Civic Hatchback

1bar_ek · Post by **1bar_ek** » September 27, 2005

Pictures are old, but they're the most recent.

Here's a picture with the t3/to4b turbo. Upgraded to the t3/to4e.

munster · Post by **munster** » September 27, 2005

Welcome to thejdm. Enjoy!

Secret Squirrel · Post by **Secret Squirrel** » September 27, 2005

awesome mang....u need a steam clean!

keep up the good work

welcome

SS

ls.pwrd.hb. · Post by **ls.pwrd.hb.** » September 27, 2005

welcome and lets see some more pics of that it looks tight

1bar_ek · Post by **1bar_ek** » September 28, 2005

Currently in the process of rebuilding the engine. Should have car up and running soon. Will have new pictures when it's up and running.

1bar_ek · Post by **1bar_ek** » September 28, 2005

Here are the mods on the hatch:

Exterior
NBP paint (01 ITR)
99-00 taillights
CTR style grille
CTR style headlights
Shaved rear wiper, antenna, emblems

Suspension
RS*R Japan lowering springs
Tokico Struts
15in. Bronze Konig Heliums
Kuhmo Ecsta Supra Tires 205/50/15s
00 Civic Si calipers
DC Sports front upper strut bar

Interior
00 Si gauge cluster
Autometer gauge cluster bezel
JVC CD/MP3 player
Clarion 5 1/4 speakers
Carbon fiber gauge overlay

Electronics
Autometer Ultra-lite (silver)
EGT gauge, Water Temp, Oil Press, A/F, Boost
Apex'i AVC-R boost controller and V-AFC vtec controller

Engine
96 B18C1 (OBDII)
Y80 tranny
ACT 6puck clutch
B16a2 flywheel
Block bored and honed to 1.85l (.020 over)
JE 9:1 forged pistons, rings, upgraded wrist pins
Eagle forged rods
ACL rod bearings
Ported and polished head
3 angle valve job
Skunk2 titanium retainers and valve springs
AEBS head studs and head bolts
SCE copper head gasket
MSD SCI ignition, plug wires, distributor cap, blaster coil
Skunk2 Intake Manifold
hondata intake manifold gasket
Turbonetics t3/t04e turbo
MPRD equal length tubular manifold, hot jet coated
SCE copper exhaust gasket
Golden eagle cam plugs
Drag downpipe flange
Spearco FMIC
Deltagate wastegate
Skunk2 cam gears
HKS SSQV blow-off valve
DSM 450cc injectors
AEM fuel rail
B&M FPR
B&M fuel pressure gauge
Drag intake pipe and filter
99-00 Si rear engine mount
Custom 3" piping with apexi turbo muffler
Walbro 255lph fuel pump
chipped P28 ecu
hasport adjustable shift linkage
skunk2 ob2-obd1 jumper harness

Tonberry · Post by **Tonberry** » September 28, 2005

welcome to thejdm!

pretty sick car man, I like the gauges. good stuff man!

YouTube · Post by **.saint** » September 29, 2005

welcome to the site! enjoy your stay.

Post by **Sean @ NDF** » September 29, 2005

welcome, nice setup