I'm excited to announce that thejdm is now updated to the latest phpbb 3.2 software. You may notice the site is now mobile friendly but with the upgrade comes some hiccups. theGarage, theGallery, theArcade are no longer supported. In due time the developers should be working to release the modifications to work on the new software. #LetsMakeForumsGreatAgain

crower 63403 cams installed

general car and site related talk and chat.
Post Reply
Hercules
50% ricer
Posts: 418
Joined: February 03, 2005
Location: Altoona, pa
Contact:
Contact Hercules

crower 63403 cams installed

Post by Hercules » May 17, 2005

well i know i shouldnt have but i put those badboys in today with stock valve train and cam gears..haha but i couldnt get her started all day i had no idea why. cause i talked to a guy the ran them with stock everything and his ran fine with stock timing and everything and i couldnt figure it out. so i'm layin in bed pissed off thinkin bout it and thought about the valve lash, thats right i didnt touch that so its like 1am but i go outside and loosin all of those bitches and finally got it started. it runs very horrible and idles like a big hammer, my timing was screw up earlier so i'm hopin that i didnt fuck my valves up, i'm gonna run a compression tester tomorrow, hopefully that goes well. but if anyone has any idea's on how to get her running OK as far as timing or whatever i can do would be greatly appreciated... :?
Top
Hercules
50% ricer
Posts: 418
Joined: February 03, 2005
Location: Altoona, pa
Contact:
Contact Hercules

Post by Hercules » May 17, 2005

anybody?! i readjusted my timing its perfect...redid the valve lash its good...but still runs like ass, it sounds like one of my plug wires is disconnected,like a lawn mower or somthin. could it be my valves bent? i havent tested the compression yet
Top
civicex2g
85% JDM
Posts: 1518
Joined: August 07, 2003
Location: Floriduh
Contact:
Contact civicex2g

Post by civicex2g » May 17, 2005

probably need to tune it?
Top
BRYCE
Posts: 5323
Joined: January 18, 2004
Location: Twin Cities, MN
Contact:
Contact BRYCE

Post by BRYCE » May 17, 2005

thats what i was thinkin possilby too much air for the amount of fuel??
AE86 Levin Coupe x SR20DET x Watanabe R-Type
Bryce
Top
Hercules
50% ricer
Posts: 418
Joined: February 03, 2005
Location: Altoona, pa
Contact:
Contact Hercules

Post by Hercules » May 20, 2005

alright just to keep you guys updated i bought a compression tester yesterday and i did bend the valves on cylinder 4. but luckily i got a new head thanks to b20rex.. but before i put her back together i'm orderin supertech valve springs so it should be bling!
Top
civicex2g
85% JDM
Posts: 1518
Joined: August 07, 2003
Location: Floriduh
Contact:
Contact civicex2g

Post by civicex2g » May 20, 2005

are you doing the whole head? or just the springs? just go for broke lol
Top
Hercules
50% ricer
Posts: 418
Joined: February 03, 2005
Location: Altoona, pa
Contact:
Contact Hercules

Post by Hercules » May 21, 2005

i pulled an all nighter last night (friday) and swapped head's along with the 403's again and she runs perfect with stock valvetrain and i reused a headgasket, lmao. dont worry i'm orderin valvesprings on monday. then i'll have to get it tuned cuz it pretty much feels the same. i'll post some pics up here in a few days of the huge lobes :D
Top
Post Reply

Return to “thejdm”