I'm excited to announce that thejdm is now updated to the latest phpbb 3.2 software. You may notice the site is now mobile friendly but with the upgrade comes some hiccups. theGarage, theGallery, theArcade are no longer supported. In due time the developers should be working to release the modifications to work on the new software. #LetsMakeForumsGreatAgain
second generation integra. [90-93]
-
AcuracyRR
- 95% ricer
- Posts: 54
- Joined: April 30, 2005
-
Contact:
Post
by AcuracyRR » September 10, 2005
Impressive find. I thought the holder I had in my old DA9 was unique, but I've never seen that setup in all honesty.
Mike
-
CDUFF7
- 80% ricer
- Posts: 169
- Joined: March 15, 2005
- Location: JAPAN
Post
by CDUFF7 » September 10, 2005
Mike, what is yours like?
-
ls.pwrd.hb.
- 75% JDM
- Posts: 1406
- Joined: June 27, 2005
Post
by ls.pwrd.hb. » September 11, 2005
thats a good find, your going to pull in a good chunk of change on that
low n slow
-
AcuracyRR
- 95% ricer
- Posts: 54
- Joined: April 30, 2005
-
Contact:
Post
by AcuracyRR » September 11, 2005
Well I currently own an '02 TL-S, but my DA-9 was everything to me. I had the armrest that was mounted with 4 screws into the sides of where the parking brake is. Then the bracket came up and there was a flat armrest. The cupholders slid forward out from the inside of padded armrest. I had seen maybe one or two other people with it in the four years I owned and built the car.
Mike
-
CDUFF7
- 80% ricer
- Posts: 169
- Joined: March 15, 2005
- Location: JAPAN
Post
by CDUFF7 » September 11, 2005
thank you for the replies,
Your type in your old DA, I have sold them too - this is not the "add on type" but the complete console, cup holders fold down from inside the lid - very smart design.
Hope everyone is seeing this and needs some good JDM parts!
-
Nikku
- Posts: 2818
- Joined: December 19, 2003
- Location: 大阪
-
Contact:
Post
by Nikku » September 12, 2005
CDUFF7 wrote:thank you for the replies,
Your type in your old DA, I have sold them too - this is not the "add on type" but the complete console, cup holders fold down from inside the lid - very smart design.
Hope everyone is seeing this and needs some good JDM parts!
better let me know first when you get another one of those b4 you post it on ebay
Just call me Dr. Vice.
-
CDUFF7
- 80% ricer
- Posts: 169
- Joined: March 15, 2005
- Location: JAPAN
Post
by CDUFF7 » September 12, 2005
Will do - they sell consistantly for over $200 on ebay. No promises but will let you know before posting.
-
Nikku
- Posts: 2818
- Joined: December 19, 2003
- Location: 大阪
-
Contact:
Post
by Nikku » September 12, 2005
CDUFF7 wrote:Will do - they sell consistantly for over $200 on ebay. No promises but will let you know before posting.
and be honest, how much did you pay for that last one? trying to figure out if i should buy from you or have one of my friends in japan go grab me one
-
CDUFF7
- 80% ricer
- Posts: 169
- Joined: March 15, 2005
- Location: JAPAN
Post
by CDUFF7 » September 12, 2005
I buy in bulk, I do not give away how much I pay, etc - you should contact your buddy - but be warned I have been looking for these for 3 years and have only found 2 - maybe your buddy will have more luck....
-
Nikku
- Posts: 2818
- Joined: December 19, 2003
- Location: 大阪
-
Contact:
Post
by Nikku » September 12, 2005
CDUFF7 wrote:I buy in bulk, I do not give away how much I pay, etc - you should contact your buddy - but be warned I have been looking for these for 3 years and have only found 2 - maybe your buddy will have more luck....
how long have you lived in japan?
